How do I setup my Fox 32 forks?
Setting Fork Air Pressure
- Unscrew the blue air cap on top of the left fork leg counter-clockwise to expose the Schrader valve.
- Attach a FOX High Pressure Pump to the Schrader valve.
- Pump your fork to the appropriate pressure as listed in the ‘Suggested starting points for setting sag’ table below, then remove the pump.
How do you set up a Fox Float shock?
Setting Shock Air Pressure
- Turn the 3-position lever to the OPEN mode.
- Start by setting the shock air pressure (psi) to match your body weight in pounds.
- Remove the pump.
- Sit still on the bike in your normal riding position, using a wall or a tree for support.
How much air should be in a Fox Float fork?
All other FOX forks can use up to a 203mm rotor (including SC 29in). Do not exceed maximum air pressure: 32 FLOAT maximum air pressure is 140 psi.
How much travel does a Fox 32 have?
The Fox 32 Factory fork is available in both 29″ and 650b wheels with 120mm of travel, a 15mm through-axle and a tapered steerer.
How much PSI is a FOX Float?
Hightower LT
| Fox Float DPX | ||
|---|---|---|
| Rider Weight | Air Pressure | Shock Sag |
| 100lbs (45.5kg) | 145 psi | 16-19 mm |
| 120lbs (54.4kg) | 165 psi | 16-19 mm |
| 140lbs (63.5kg) | 180 psi | 16-19 mm |
How much air should I put in my bike shocks?
For the rear shock, start at about half of your rider weight for air pressure. You will have to adjust from here, but you will want to achieve the proper SAG for your frame, as recommended by your frame manufacturer. Typically this is somewhere between 30-40% of overall travel.
What PSI is Fox 34?
200 psi
34 TALAS maximum air pressure is 200 psi. The recommended settings in this tuning guide are designed to be a starting point, in order to get you out on your first ride in as few steps as possible.
How much PSI is a Fox Float?
Blur
| FOX Float DPS | ||
|---|---|---|
| Rider Weight | Air Pressure | Shock Sag |
| 120lbs (54.4kg) | 150 psi | 9-11mm |
| 140lbs (63.5kg) | 175 psi | 9-11mm |
| 160lbs (72.6kg) | 200 psi | 9-11mm |
How much air should I put in my Fox 36?
Generally, sag should be set to 15 – 25% of total fork travel. Unscrew the center blue aircap (shown below) on top of the left fork leg to expose the Schrader valve….Setting Sag.
| 36 float AIR SPRING SETTING guidelines | |
|---|---|
| Rider Weight | Air Pressure |
| 145 – 155 lbs. | 53 psi |
| 155 – 170 lbs. | 55 psi |
| 170 – 185 lbs. | 62 psi |
What kind of remote does float Fox ridefox use?
Factory FIT CTD Remote; 80, 100, 120, 140 & 150: Kashima coated or hard anodized upper tubes, 1.5″ tapered or 1 1/8″ steerer, remotely actuated 3-position Climb/Trail/Descend, air spring pressure, rebound
Where is the rebound adjuster on a float Fox?
Measure sag again and repeat this adjustment if necessary. Screw the blue aircap back on, and go ride. The rebound adjuster knob is located at the bottom of the right fork leg. Rebound controls the rate of speed at which the fork extends after compressing.
How big is a terralogic float Fox ridefox?
Factory FIT Terralogic®; 80, 100, 120: Kashima coated or hard anodized upper tubes, 1.5″ tapered steerer or 1 1/8″ steerer, Terralogic® threshold, air spring pressure, rebound