How do you fix a cutter error?

Follow these steps to resolve the issue.

  1. Press the POWER key to turn the machine off.
  2. Open the tape compartment cover and remove the tape cassette.
  3. Examine the area by the two black rollers and the tape exit area.
  4. Reinstall the tape cassette into the machine and close the tape compartment cover.

Why is my Brother P Touch label maker not printing?

The label is not printed after pressing the Print key. Check that the text has been entered and that the tape cassette has been properly installed with sufficient tape remaining. If the tape is bent, cut off the bent section and thread the tape through the tape exit slot.

How do I reset my brother label maker PT 1290?

Reset the label printer

  1. Turn off the label printer.
  2. Hold down Shift and the letter R key.
  3. While holding down the keys, press the Power key once to turn on the label printer.
  4. Release the keys.

How do you lower the margins on a Brother label maker?

How do I adjust the tape margins?

  1. Press the Fn (Function) key.
  2. Press the LEFT or the RIGHT arrow key until Margin is displayed.
  3. Press the OK key; the current margin setting will be on the display.
  4. There are four options, Full, Half, Narrow, and Chain Print.
  5. Press the OK key to apply the selected margin.

Why is my printer not cutting?

Be sure to clean the cutting mechanism of any debris. This will prevent it from cutting the receipt paper. Open the printer cover to check to make sure there is enough paper on the receipt roll and that is has not bunched up inside the hardware. Make sure there is no debris on the paper, the cutter, or the print head.

How do I fix my Dymo label maker Cutter?

Fixing a jammed cutter on a Dymo Rhino 6000

  1. Switch off the printer.
  2. Press and hold the cut key and switch the device back on.
  3. The message “CUT TEST” should be displayed on the device’s display.
  4. Press and hold the “shift” key and press the cut key.
  5. Try cleaning anything around the blade that might have caused the jam.

Why won’t My Brother P-Touch won’t turn on?

If the batteries are running low, the power will not turn on. The P-touch resets to the default setting when more than 3 minutes pass after the batteries are removed, or the P-touch is disconnected from the AC adapter without using batteries.

How do I reset my brother pt 65?

Reset the label machine

  1. Turn off the label machine.
  2. Hold down the Code key and the Clear (BS) key.
  3. While holding down the keys, press the On/Off key once to turn on the label machine.
  4. Release the keys.

How do I clear the settings on my Brother label maker?

Reset the label machine

  1. Hold down the Shift key and the letter R key.
  2. While holding down the keys, press the Power key once to turn on the label machine.
  3. Release the keys. “English” should be displayed.
  4. – If “English” is not displayed, repeat step 1 – 4.
  5. “inch” will be displayed and press the Enter key.

How do I clear the P Touch label maker?

You can reset the internal memory of your P-touch when you want to clear all saved label files, or in the event the P-touch labeler is not operating correctly. Turn off the P-touch. While holding down the Shift and R keys, press the Power key to turn the P-touch back on. Release the Shift and R keys.

How do I change the settings on my Brother label maker?

To change the length of the label,

  1. Press the [Label] key ( / ). The current settings are displayed.
  2. Select the “Length” attribute using the or key, and then set a value using the or. key.
  3. Press the [OK] key ( ) or [Enter] key ( / ) to apply the settings.

How do I stop my brother p touch from wasting tape?

How to Keep a Brother P-Touch From Wasting Tape

  1. Press the Power key located on the upper left side of the device.
  2. Type your label using the keyboard.
  3. Press the “Function” key, located in the center of the P-Touch.
  4. Press the right arrow key until “Length” appears on the display, then press the Return key.